Connection swirl with swivel, stainless steel (corrosion free), Ø 30 mm/1,1811 in., max. pull force

Connection swirl with swivel, stainless steel (corrosion free), Ø 30 mm/1,1811 in., max. pull force

235.50 CHF

Connection swirl with swivel, stainless steel (corrosion free), Ø 30 mm/1,1811 in., max. pull force

235.50 CHFThe connecting swirl with swivel is used to connect RUNPOTEC polyester pulling ropes with the cables to be pulled or the deployed pulling die and to ensure swivel. Ideally suited in combination with the RUNPOTEC CW 800 E capstan winch. Made of stainless steel, with the highest quality ball bearings, make the connecting swivel from RUNPOTEC completely corrosion-free and thus one of the highest quality products on the market. Max. pull force 1500 kg. Safety instructions: Not suitable for vertical cable pulling, must not be used to carry or lift loads or persons. Optimal application: for horizontal cable pulling in combination with the CW 800 E capstan winch Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x Connecting swirl with swivel
Conversion kit CW 800 E capstan winch to model 2025, 6-piece, stainless steel, in approx. 20 min.

Conversion kit CW 800 E capstan winch to model 2025, 6-piece, stainless steel, in approx. 20 min.

550.00 CHF

Conversion kit CW 800 E capstan winch to model 2025, 6-piece, stainless steel, in approx. 20 min.

550.00 CHFThe conversion kit contains all the parts required to convert a CW 800 E capstan winch purchased before October 2025 to the technical standard of the CW 800 E - Model 2025, thereby benefiting from the improved functions. The conversion takes around 20 minutes and detailed instructions are included. Both capstan heads have been widened in the new CW 800 E model 2025. The rope wrapping area on the Ø 55 capstan head has been increased from 8.5 cm to 10.5 cm, and on the Ø 110 capstan head from 6.5 cm to 8.5 cm. In addition, a knurled surface has been integrated at the end of the capstans, which increases friction and reduces the pulling force required by the operator. The maximum pulling load remains unchanged at 400 kg and 800 kg respectively. The rope guide jaws have also been redesigned. They now surround the respective capstan head, ensuring better rope guidance and significantly less rope wear. Due to the redesign, the rope entry and rope exit also had to be renewed. The corresponding parts are included. Scope of supply: 1 x Conversion kit CW 800 E capstan winch to model 2025
CW 800 E - capstan winch, incl. 3 m/9,84 ft. strap, motor connection 230 V / 50 Hz, selectable

CW 800 E - capstan winch, incl. 3 m/9,84 ft. strap, motor connection 230 V / 50 Hz, selectable

2'709.00 CHF

CW 800 E - capstan winch, incl. 3 m/9,84 ft. strap, motor connection 230 V / 50 Hz, selectable

2'709.00 CHFIdeally suited for horizontal pulling of one or more cables. Where several persons are needed for higher pulling loads on many sites, one person is sufficient to pull in the cables with the CW 800 E capstan winch by RUNPOTEC with a choice of 800 kg or 400 kg. The capstan winch can be fixed via the mounting holes or attached to solid objects with the enclosed strap. Safety instructions: Not suitable for vertical cable pulling, must not be used to carry or lift loads or persons. Optimal area of application: for horizontal cable pulling. Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x Capstan winch CW 800 E, 1 x 3 m strap
CW 800 E - capstan winch, incl. trolley mounting rail and 3 m/9,84 ft. strap, motor connection 230 V

CW 800 E - capstan winch, incl. trolley mounting rail and 3 m/9,84 ft. strap, motor connection 230 V

2'828.00 CHF

CW 800 E - capstan winch, incl. trolley mounting rail and 3 m/9,84 ft. strap, motor connection 230 V

2'828.00 CHFIdeally suited for horizontal pulling of one or more cables. Where several persons are needed for higher pulling loads on many sites, one person is sufficient to pull in the cables with the CW 800 E capstan winch by RUNPOTEC with a choice of 800 kg or 400 kg. The capstan winch can be fixed via the mounting holes or attached to solid objects with the enclosed strap. The trolley mounting rail also offers a very practical fastening option. It can be attached to the trailer hitch of a vehicle through the special coupling opening. It is also possible to mount the rail horizontally or vertically, and then simply hook in the CW 800 E capstan winch and fasten it using the two fixing bolts. Safety instructions: Not suitable for vertical cable pulling, must not be used to carry or lift loads or persons. Optimal area of application: for horizontal cable pulling. Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x Capstan winch CW 800 E, 1 x trolley mounting rail, 1 x 3 m strap
Fiberglass rod Ø 3 mm - length: 2 x 1 m, thread RTG Ø 6 mm

Fiberglass rod Ø 3 mm - length: 2 x 1 m, thread RTG Ø 6 mm

17.70 CHF

Fiberglass rod Ø 3 mm - length: 2 x 1 m, thread RTG Ø 6 mm

17.70 CHFThe fibreglass rod (Ø 3 mm, length 1 m) is mainly used in combination with RUNPOSTICKS as an additional guide probe. The standard RTG Ø 6 mm thread allows for a wide variety of combinations. All accessories can be screwed on without the need for an additional adapter. It can also be easily combined with the RC3, which expands its range of applications. Optimal area of application: suspended ceilings, cable ducts, cavity walls, rewiring of unguided cables, underfloor ducts, feed-throughs, etc. Scope of supply: 2 x Fiberglass rod Ø 3 mm - Length: 1 m
Flexible leading head-set - RUNPOSTICKS, 13 parts, basalt rod - plastic-coated, stowed in storage

Flexible leading head-set - RUNPOSTICKS, 13 parts, basalt rod - plastic-coated, stowed in storage

120.50 CHF

Flexible leading head-set - RUNPOSTICKS, 13 parts, basalt rod - plastic-coated, stowed in storage

120.50 CHFThe use of the RUNPOSTICKS creates a flexible guide tip, which allows tighter bends to be overcome without any problems. The rods can each be extended by 1 m and can be adapted as softer guide probes to fiberglass rods Ø 7.5 mm, Ø 9 mm and also Ø 11 mm. In addition, it is also possible to screw on accessories at the tip, such as rollers or RUNPOGLIDER with swivel. Scope of supply: 1 x Flexibel leading head-set - RUNPOSTICKS 13-piece consisting of: 2 x RUNPOSTICKS yellow Ø 4.5 mm (soft), 2 x RUNPOSTICKS black Ø 5.5 mm (medium), 2 x RUNPOSTICKS red Ø 7.5 mm (hard), 1 x RUNPOGLIDER with front thread, 1 x roller Ø 25 mm, 3 x coupling joint, 1 x blind cap, 1 x starting head Ø 20 mm RTG Ø 12mm, 1 x storage bag
GF11 - Fiberglass rod Ø 11 mm/0,4331 in. with RUNPOTEC thread RTG Ø 12 mm, cable pulling tool,

GF11 - Fiberglass rod Ø 11 mm/0,4331 in. with RUNPOTEC thread RTG Ø 12 mm, cable pulling tool,

878.00 CHF

GF11 - Fiberglass rod Ø 11 mm/0,4331 in. with RUNPOTEC thread RTG Ø 12 mm, cable pulling tool,

878.00 CHFCable puller fiberglass rod (duct rodders) Ø 11 mm - RUNPOTEC RTG Ø 12 mm thread with robust steel reel (CDP/powder coated) Ø 1000 mm incl. new double run-out system (automatic run-out brake and fast run-out), additional parking brake. The shackle also has a transition thread to RTG Ø 6 mm to adapt various guide rods (RUNPOSTICKS), guide probes, cable pulling grip (sock), multifunction camera RC 2 and the like. Fiberglass rod breaking load 6200 kg, total breaking load 580 kg. Optimal field of application: for pipe diameters 80 - 250 mm Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x GF11 fiberglass rod Ø 11 mm, Length: 100 m, ending joint with RUNPOTEC thread Ø 12 mm on both sides (start/end), 1 x mobile steel reel Ø 1000 mm incl. double run-out system, 1 x metercounter, 1 x shackle
GF11 - Fiberglass rod Ø 11 mm/0,4331 in. with RUNPOTEC thread RTG Ø 12 mm, cable pulling tool,

GF11 - Fiberglass rod Ø 11 mm/0,4331 in. with RUNPOTEC thread RTG Ø 12 mm, cable pulling tool,

953.00 CHF

GF11 - Fiberglass rod Ø 11 mm/0,4331 in. with RUNPOTEC thread RTG Ø 12 mm, cable pulling tool,

953.00 CHFCable puller fiberglass rod (duct rodders) Ø 11 mm - RUNPOTEC RTG Ø 12 mm thread with robust steel reel (CDP/powder coated) Ø 1000 mm incl. new double run-out system (automatic run-out brake and fast run-out), additional parking brake. The shackle also has a transition thread to RTG Ø 6 mm to adapt various guide rods (RUNPOSTICKS), guide probes, cable pulling grip (sock), multifunction camera RC 2 and the like. Fiberglass rod breaking load 6200 kg, total breaking load 580 kg. Optimal field of application: for pipe diameters 80 - 250 mm Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x GF11 fiberglass rod Ø 11 mm, Length: 120 m, ending joint with RUNPOTEC thread Ø 12 mm on both sides (start/end), 1 x mobile steel reel Ø 1000 mm incl. double run-out system, 1 x metercounter, 1 x shackle
GF11 - Fiberglass rod Ø 11 mm/0,4331 in. with RUNPOTEC thread RTG Ø 12 mm, cable pulling tool,

GF11 - Fiberglass rod Ø 11 mm/0,4331 in. with RUNPOTEC thread RTG Ø 12 mm, cable pulling tool,

1'052.00 CHF

GF11 - Fiberglass rod Ø 11 mm/0,4331 in. with RUNPOTEC thread RTG Ø 12 mm, cable pulling tool,

1'052.00 CHFCable puller fiberglass rod (duct rodders) Ø 11 mm - RUNPOTEC RTG Ø 12 mm thread with robust steel reel (CDP/powder coated) Ø 1000 mm incl. new double run-out system (automatic run-out brake and fast run-out), additional parking brake. The shackle also has a transition thread to RTG Ø 6 mm to adapt various guide rods (RUNPOSTICKS), guide probes, cable pulling grip (sock), multifunction camera RC 2 and the like. Fiberglass rod breaking load 6200 kg, total breaking load 580 kg. Optimal field of application: for pipe diameters 80 - 250 mm Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x GF11 fiberglass rod Ø 11 mm, Length: 150 m, ending joint with RUNPOTEC thread Ø 12 mm on both sides (start/end), 1 x mobile steel reel Ø 1000 mm incl. double run-out system, 1 x metercounter, 1 x shackle

<< < 1 2 3 ... > >>