2 components special glue 24 ml, 2-component

2 components special glue 24 ml, 2-component

25.80 CHF

2 components special glue 24 ml, 2-component

25.80 CHFOperational area: 2 K - Special adhesive 24 ml for repairing 6 mm, 7 mm, 11 mm and 15 mm fiberglass rods. 20% more adhesive strength compared to superglue. The 2-component special adhesive is transparent and offers very high resistance. For instructions see safety data sheet! Scope of supply: 1 x 2 components special glue 24 ml
Adhesive joint Set GF3 - Ø 3 mm/0,1181 in., 6 pieces,

Adhesive joint Set GF3 - Ø 3 mm/0,1181 in., 6 pieces,

7.10 CHF

Adhesive joint Set GF3 - Ø 3 mm/0,1181 in., 6 pieces,

7.10 CHFAdhesive joint set made of brass for GF3 glass fibre rod Ø 3 mm. The adhesive joint is glued to the glass fibre rod with the special adhesive and thus serves as a connecting piece between the glass fibre rod and the kink protection ending joint. In this way, any break points can be repaired. Scope of supply: 6 x adhesive joints GF3 Ø 3 mm
Adjust the diameter for the respective cable by turning the setting wheel. Cable width Multi-jaws

Adjust the diameter for the respective cable by turning the setting wheel. Cable width Multi-jaws

27.30 CHF

Adjust the diameter for the respective cable by turning the setting wheel. Cable width Multi-jaws

27.30 CHF"With the RM35 Multi-jaws - round, optimal or highly precise measuring results can be achieved with the RM35 - Digital cable length measuring device. Insert the RM35 multi-jaws in pairs, with the selected diameter facing upwards, into the opening provided. Adjust the diameter for the respective cable by turning the setting wheel: Cable diameter Multi-jaws Ø 2 - 3 mm Ø 3 mm Ø 3 - 4 mm Ø 4 mm Ø 4 - 6 mm Ø 6 m Ø 6 - 8 mm Ø 8 mm Ø 8 - 10 mm Ø 10 mm Ø 10 - 12 mm Ø 12 m Ø 12 - 15 mm Ø 15 m Optimum application: with RM35 - digital cable length measuring device Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x multi jaws RM35 - round"
Adjust the width for the respective cable by turning the setting wheel. Cable width Multi-jaws Width

Adjust the width for the respective cable by turning the setting wheel. Cable width Multi-jaws Width

27.30 CHF

Adjust the width for the respective cable by turning the setting wheel. Cable width Multi-jaws Width

27.30 CHFWith the multi jaws RM35 - angular, optimal or highly precise measuring results of angular cables, such as duplex cables, LED tape, flat ribbon cables, etc. can be achieved with the RM35 - digital cable length measuring device. Insert the RM35 multi-jaws in pairs, with the selected width facing upwards, into the opening provided. Adjust the width for the respective cable by turning the setting wheel: Cable width Multi-jaws 2 - 3 mm Width 3 mm 3 - 4 mm Width 4 mm 4 - 6 mm Width 6 mm 6 - 8 mm Width 8 mm 8 - 10 mm Width 10 mm 10 - 12 mm Width 12 mm 12 - 15 mm Width 15 mm Optimal application: with RM35 - digital cable length measuring device Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of delivery: 2 x multi-jaws RM35 - angular, 3 - 15 mm
Attachment flexible 12 cm/4,7244 in. - thread RTG Ø 6 mm, stainless

Attachment flexible 12 cm/4,7244 in. - thread RTG Ø 6 mm, stainless

9.90 CHF

Attachment flexible 12 cm/4,7244 in. - thread RTG Ø 6 mm, stainless

9.90 CHFApplication: mainly used in combination with the RUNPOCAM RC2 multifunctional camera to create individual angles or bends. This makes it possible to make various angle settings even over long distances (see Application video RUNPOCAM RC2). Also ideally suited for the RUNPOSTICKS. Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x Attachment flexible 12 cm with RTG Ø 6 mm thread
Ball chain with thread RTG Ø 6 mm, Length: 0,5 m/1,64 ft., stainless steel, total breaking load 25

Ball chain with thread RTG Ø 6 mm, Length: 0,5 m/1,64 ft., stainless steel, total breaking load 25

12.60 CHF

Ball chain with thread RTG Ø 6 mm, Length: 0,5 m/1,64 ft., stainless steel, total breaking load 25

12.60 CHFAccessories for RUNPOSTICKS. In combination with the magnet, targeted locating or guiding of the chain to wall openings is possible. Optimal area of application: suspended ceilings, cable shafts, hollow walls, retroactive wiring of non-routed cables, underfloor shafts, bushings etc. Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x Ball chain with thread RTG Ø 6 mm, length: 0,5 m
Belt with clip system and connecting pad, belt length 1200 mm/47,2441 in.,

Belt with clip system and connecting pad, belt length 1200 mm/47,2441 in.,

40.70 CHF

Belt with clip system and connecting pad, belt length 1200 mm/47,2441 in.,

40.70 CHFUsing the belt and clip system, the RUNPOMETER RM35 can be easily connected to the X BOARD XB 300 or XB 500 cable unwinding system. The belt is adjustable from 750 mm to 1200 mm (article number 20706) and from 1360 mm to 2400 mm article number 20714). Alternatively, the belt can also be connected to the anchor pad, which then offers an anchoring option for all conventional unwinding systems. The belt with clip system can also be connected to the RUNPOTEC cable pulling systems (professional set fiberglass rod Ø 4.5 mm and 6 mm etc.). This variant is also suitable for anchoring the RUNPOMETER RM35 on rods or columns. Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x Belt with clip system - length 1200 mm, 1 x connecting pad
Belt with clip system and connecting pad, belt length 2400 mm/94,4882 in.,

Belt with clip system and connecting pad, belt length 2400 mm/94,4882 in.,

46.50 CHF

Belt with clip system and connecting pad, belt length 2400 mm/94,4882 in.,

46.50 CHFUsing the belt and clip system, the RUNPOMETER RM35 can be easily connected to the X BOARD XB 300 or XB 500 cable unwinding system. The belt is adjustable from 750 mm to 1200 mm (article number 20706) and from 1360 mm to 2400 mm (article number 20714). Alternatively, the belt can also be fixed to the connecting pad, which then offers an anchoring option for all conventional unwinding systems. The belt with clip system can also be connected to the RUNPOTEC cable pulling systems (professional set fiberglass rod Ø 4.5 mm and 6 mm etc.). This variant is also suitable for anchoring the RUNPOMETER RM35 on rods or columns. Application video: a short, very informative application video can be viewed by scanning the QR code or on www.RUNPOTEC.com. Scope of supply: 1 x Belt with clip system - length 2400 mm, 1 x connecting pad
Blind cap set with thread RTG Ø 6 mm, 3 pieces, stainless

Blind cap set with thread RTG Ø 6 mm, 3 pieces, stainless

7.40 CHF

Blind cap set with thread RTG Ø 6 mm, 3 pieces, stainless

7.40 CHFFor sealing RTG Ø 6 mm transition threads. Protects the RTG Ø 6 mm transition thread against dirt, such as on the roller, shackle or the two starting bulbs Ø 20 and 30 mm. Can also be used in combination with the RUNPOSTICKS as a shock or protection cap. Scope of supply: 3 x Blind caps with RTG Ø 6 mm thread

<< < 1 2 3 ... > >>